OUR PRODUCTS

Apply for Agency/Distributionship

JCK PU Topcoat Lacquer Clear

JCK_N.C_Lacquer_Thinner_X_(71102)

Product Code : 4010/500 PU Topcoat Lacquer Clear 10% Sheen
: 4030/500 PU Topcoat Lacquer Clear 30% Sheen
: 4099/500 PU Topcoat Lacquer High Gloss

Product Description


JCK PU Topcoat Lacquer Clear is Isocyanate based 2 pack products for wood finishing applications.

Performance Features & Benefits


JCK PU Topcoat Lacquer Clear is a fast drying non yellowing product with unmatched transparency and tough film characteristics. The product shows superb scratch, mar and chemical resistance. It is available in three variants based on sheen levels like 10%, 30% and High Gloss respectively.

Recommended Usage


JCK PU Topcoat Lacquer Clear can be used for finishing of wooden surfaces like Veneers, Natural Wood, Plywood for Table Tops, Doors, Cabinets, Chairs, Beds, etc.

Recommended Application


Sand the wooden surface along the grains using emery paper no. 180. This should be followed by smooth sanding with emery paper no. 320. Wipe the surface to clean off loose dust particles. Mix Base + Hardener +Thinner in Ratio of 100:50:15 Ratio and give 10 minutes maturation time and spray apply.


Apply coating as follows:-

  Catalyst %(by volume ) Thinner %(by volume) Application viscosity (sec)
JCK PU Basecoat Coat 1st Spraying JCK 40CT40 PU Catalyst for Basecoat 50% JCK PU Thinner (74400) 15%-25% 18 – 20 sec
Sand with emery paper 320 or 400 and wipe clean      
JCK PU Basecoat 2 nd Coat Spraying JCK 40CT40 PU Catalyst for Basecoat 50% JCK PU Thinner (74400) 15%-25% 18 – 20 sec
Sand with emery paper 320 or 400 and wipe clean      
JCK PU Topcoat Lacquer Clear (Required sheen level variant) 1st Coat Spraying JCK 40CT50 P U Catalyst for Topcoat 50% JCK PU Thinner (74400) 10%-20% 17 – 19 sec
Sand with emery paper 320 or 400 and wipe clean      
JCK PU Topcoat Lacquer Clear( Required sheen level variant) 2nd Coat Spraying JCK 40CT50 P U Catalyst for Topcoat 50% JCK PU Thinner (74400) 10%-20% 17 – 19 sec

Note :

  • Spraying - Air Pressure 2.2 to 2.8 Kgs/sq.cm
  • Application Viscosity as measured by Ford Cup B4 at 30° C

Technical Data


  • Coverage* : 8 — 9 sq.mtr/Itr/coat
  • Drying Time : Dry to touch time — 10 minutes, Recoating time — 45 minutes
  • Flash Point : (IS 101/1987, Part 1, Sec 6) : below 5°C d) Stability of Thinned Paint : Use within 24 hours
  • Shelf Life: 2 Years from the date of manufacture in original tightly closed containers kept away from direct sunlight and excessive heat

Pack size availability:


1 Ltr 4 Ltr 20 Ltr

Disclaimer


Information contained in this technical data sheet is believed to be reliable and given in good faith and based on our present knowledge, but no representation, guarantee or warranties of any kind are made as to its accuracy, suitability for a particular application or results to be obtained from them. The user of this material decides what safety measures are necessary to safely use this material, either alone or in combination with other materials. JCK Coating Industries cannot anticipate or control the conditions under which this information may be used. Therefore, it is user’s responsibility to satisfy themselves as to the suitability and completeness of such information for their particular use. It is the responsibility of the user to determine the final suitability of this information and data and to comply with all applicable international, federal, state, and local laws and regulations. It is the responsibility of the user to ensure that the issue is current. This information given is a non-controlled document.

Thinners